WIZARD LIGHTSTM
Installation Guide
Parts Included:
4 – Cage Clamp® Connectors
2 - Crimp n Seal™ Spade Connectors
1 - 3M Adhesive Promoter
10 – Tie Wraps
1 – Roll 3M Tape
TOOLS YOU SHOULD HAVE TO DO THIS JOB
WIRE STRIPERS
WIRE CRIMPERS
OPEN END WRENCHS
ISOPROPAL ALCOHOL AND RAG
MAKE SURE BIKE IS COOL AND PARKED ON A FLAT SECURE SURFACE
NEXT LOCATE THE BATTERY AND UNHOOK THE BATTERY NEGITIVE (-) CABLE. (REMOVE
SEAT OR SIDE COVERS AS NEEDED TO GAIN ACCESS TO THIS AREA).
******* SAFETY CAUTION! *******
NEGITIVE (-) BATTERY CABLE MUST BE UNHOOKED FIRST TO AVOID FIRE HAZARD!
PICK A MOUNTING LOCATION FOR WIZARD LIGHT PODS IN ORDER TO GIVE BEST OVERALL
COVERAGE OF LIGHT.
WE RECOMMEND CLEANING THE MOUNTING AREAS WITH ISOPROPAL ALCOHOL FIRST.
NEXT, WIPE THE MOUNTING AREAS WITH THE ENCLOSED 3M PROMOTER PAD.
Note: Wizard Lights come pre-tape with 3M tape on the back surface, we have included extra tape so that if you
need to mount a Wizard Light on its side surface you can.
RUN THE WIRES FROM THE WIZARD LIGHT UNITS TO A CENTRAL POINT NEAR THE BATTERY.
CUT WIRES TO LENGTH AS NEEDED BEING SURE TO LEAVE ENOUGH SLACK TO ALLOW FOR
STRIPPING AND JOINING THE WIRES TOGETHER..
TRIM BACK OUTER BLACK COVER FROM LEADS AS NEEDED TO ALLOW ACCESS FOR STRIPPING
INNER WIRES INSULATION BACK APROXITMATLY 1/2 OF AN INCH.
PICK A LOCATION FOR THE COLOR COMAND MODULE THAT WILL ALLOW IT’S LEADS TO
REACH TO BOTH THE BATTERY AND TO THE WIRES FROM THE WIZARD LIGHT UNITS.
STRIP BACK THE INSULATION APROXIMATLY 1/2 OF AN INCH FROM THE 3 WHITE WIRES AND
ONE OF THE BLACK WIRES FROM THE COLOR COMAND MODULE.
JOIN WIRES FROM COLOR COMAND MODULE TO THE WIZARD LIGHT UNITS AS FOLLOWS:
2
JOIN ANY ONE OF THE WHITE WIRES FROM THE COLOR COMAND MODULE TO THE REDS WIRE
FROM THE WIZARD LIGHT UNITS USING ONE CAGE CLAMP CONNECTOR. LEFT LEVER ARM,
INSERT WIRES, LOCK LEVER ARM.
REPETE USING ANY ONE OF THE REMAINING WHITE WIRES FROM THE COLOR COMAND
MODULE TO THE BLUE WIRES FROM THE WIZARD LIGHT UNITS USING THE SECOND CAGE
CLAMP CONNECTOR..
NEXT, JOINING THE LAST WHITE WIRE FROM THE COLOR COMAND MODULE TO THE GREEN
WIRES FROM THE WIZARD LIGHT UNITS USING THE THIRD CAGE CLAMP CONNECTOR.
FINISH BY JOING ONE OF THE BLACK WIRES FROM THE COLOR COMAND MODULE TO THE
BLACKS FROM THE WIZARD LIGHT UNITS USING THE LAST CAGE CLAMP CONNECTOR.
THE BLUE WIRE IS THE ANTENNA, DO NOT CONNECT TO ANYTHING.
NEXT, LOCATE AND REMOVE FUSE FROM FUSE HOLDER IN COLOR COMAND MODULE RED
INPUT LEAD.
AFTER REMOVING FUSE, CRIMP SPADE CONNECTOR ONTO END OF RED INPUT LEAD TO COLOR
COMAND MODULE THEN CONNECT LEAD TO POSITIVE TERMINAL ON BATTERY.
REPETE CRIMPING PROCEDURE FOR REMAINING BLACK WIRE FROM COLOR COMAND MODULE.
THIS TIME HOOKING BLACK LEAD TO NEGITIVE TERMINAL ON BATTERY. AT THIS TIME ALSO
REHOOK NEGITIVE CABLE TO BATTERY.
REINSTALL FUSE INTO FUSE HOLDER.
*******SAFETY CAUTION!*******
NEVER RUN A HIGHER THAN 3 AMP FUSE IN SYSTEM!
UNIT DAMAGE OR FIRE HAZARD CAN RESULT!
PRESS THE ON BUTTON ON THE REMOTE, ENJOY THE SHOW!
COMPLETE CONTROL FUNCTIONS FOR THE COLOR COMAND MODULE ARE CONTAINED INSIDE EACH
COLOR COMAND MODULE BOX. PLEASE REVIEW OPERATAING INSTRUCTIONS FOR THE COLOR COMAND
MODULE PRIOR TO USE.
NOW ENJOY THE SHOW!
BECAUSE WITH
WIZARD LIGHTS™
YOU’VE GOT
“TOTAL CONTROL IN THE PALM OF YOUR HAND” ™
3
CAGE CLAMP® Instructions
Strip wire 9 - 10 mm. Use the stripped wire gauge on the back of the connector to verify correct strip length.
Connection: Push up lever and insert conductor . . .
. . . then push down lever to its closed position